5.9. Failover and Failback

5.9.1. Failover and Failback Settings

failover_command (string)

Specifies a user command to run when a PostgreSQL backend node gets detached. Pgpool-II replaces the following special characters with the backend specific information.

Table 5-6. failover command options

Special characterDescription
%dDB node ID of the detached node
%hHostname of the detached node
%pPort number of the detached node
%DDatabase cluster directory of the detached node
%MOld master node ID
%m New master node ID
%HHostname of the new master node
%P Old primary node ID
%rPort number of the new master node
%RDatabase cluster directory of the new master node
%% '%' character

Note: The "master node" referes to a node which has the "youngest (or the smallest) node id" among live the database nodes. In streaming replication mode, this may be different from primary node. In Table 5-6, %m is the new master node chosen by Pgpool-II. It is the node being assigned the youngest (smallest) node id which is alive. For example if you have 3 nodes, namely node 0, 1, 2. Suppose node 1 the primary and all of them are healthy (no down node). If node 1 fails, failover_command is called with %m = 0.

Note: When a failover is performed, basically Pgpool-II kills all its child processes, which will in turn terminate all the active sessions to Pgpool-II. After that Pgpool-II invokes the failover_command and after the command completion Pgpool-II starts new child processes which makes it ready again to accept client connections.

However from Pgpool-II 3.6, In the steaming replication mode, client sessions will not be disconnected when a fail-over occurs any more if the session does not use the failed standby server. If the primary server goes down, still all sessions will be disconnected. Health check timeout case will also cause the full session disconnection. Other health check error, including retry over case does not trigger full session disconnection.

This parameter can be changed by reloading the Pgpool-II configurations.

failback_command (string)

Specifies a user command to run when a PostgreSQL backend node gets attached to Pgpool-II. Pgpool-II replaces the following special characters with the backend specific information. before excuting the command.

Table 5-7. failback command options

Special characterDescription
%dDB node ID of the attached node
%hHostname of the attached node
%pPort number of the attached node
%DDatabase cluster directory of the attached node
%MOld master node ID
%m New master node ID
%HHostname of the new master node
%P Old primary node ID
%rPort number of the new master node
%RDatabase cluster directory of the new master node
%% '%' character

This parameter can be changed by reloading the Pgpool-II configurations.

follow_master_command (string)

Specifies a user command to run after failover on the primary node failover. This works only in Master Replication mode with streaming replication. Pgpool-II replaces the following special characters with the backend specific information before excuting the command.

Table 5-8. follow master command options

Special characterDescription
%dDB node ID of the detached node
%hHostname of the detached node
%pPort number of the detached node
%DDatabase cluster directory of the detached node
%MOld master node ID
%m New master node ID
%HHostname of the new master node
%P Old primary node ID
%rPort number of the new master node
%RDatabase cluster directory of the new master node
%% '%' character

Note: If follow_master_command> is not empty, then after failover on the primary node gets completed in Master Slave mode with streaming replication, Pgpool-II degenerates all nodes excepted the new primary and starts new child processes to be ready again to accept connections from the clients. After this, Pgpool-II executes the command configured in the follow_master_command for each degenerated backend nodes.

Typically follow_master_command command is used to recover the slave from the new primary by calling the pcp_recovery_node command.

This parameter can be changed by reloading the Pgpool-II configurations.

fail_over_on_backend_error (boolean)

When set to on, Pgpool-II considers the reading/writing errors on the PostgreSQL backend connection as the backend node failure and trigger the failover on that node after disconnecting the current session. When this is set to off, Pgpool-II only report an error and disconnect the session in case of such errors.

Note: It is recommended to turn on the backend health checking (see Section 5.8) when fail_over_on_backend_error is set to off. Note, however, that Pgpool-II still triggers the failover when it detects the administrative shutdown of PostgreSQL backend server.

This parameter can be changed by reloading the Pgpool-II configurations.

search_primary_node_timeout (integer)

Specifies the maximum amount of time in seconds to search for the primary node when a failover scenario occurs. Pgpool-II will give up looking for the primary node if it is not found with-in this configured time. Default is 300 and Setting this parameter to 0 means keep trying forever.

This parameter is only applicable in the streaming replication mode.

This parameter can be changed by reloading the Pgpool-II configurations.

5.9.2. Failover in the raw Mode

Failover can be performed in raw mode if multiple backend servers are defined. Pgpool-II usually accesses the backend specified by backend_hostname0 during normal operation. If the backend_hostname0 fails for some reason, Pgpool-II tries to access the backend specified by backend_hostname1. If that fails, Pgpool-II tries the backend_hostname2, 3 and so on.